KNAUF TILE ADHESIVE KNAUF EXTRA C1TE GRAY 25KG
Knauf tile glue extra C1TE gray 25KgCement basedExcellent durability and strong adhesive power
ISOMAT DUROCRET RESIN REPAIRING CEMENT MORTAR GRAY 25KG
Resin repair cement mortar. Suitable for repairs of concrete surfaces, masonry, plasters, construction of gable roofs, construction of gutters, etc.
ISOMAT TILES ADHESIVE AK-16 25KG WHITE
ISOMAT AK16 is a high performance, cement base polymer-modified adhesive. It offers highinitial and final adhesive strength and resistance to moisture. It is qualified as absolutely non-slip and shows increased open time.It is classified as type C2TE adhesive according to EN 12004.Fields of applicationISOMAT AK 16 is suitable for fixing absorbent or non-absorbent tiles (e.g. “gres porcellanato”), on walls or floors on varioussubstrates, especially where particularly high adhesion, elasticity and moisture resistance are required. It is suitable for indoor or outdoor use.Technical dataForm: cementitious mortarColors: grey, whiteWater demand: 6.75 kg/25 kg bagApplication temperature: from +50ºC to +350ºCApplication thickness: up to 15 mmPot life: at least 6 hOpen time: at least 30 minMinor adjustmentsopen time: at least 30 minPointing on walls: after 3-8 hPointing on floors: after 24 hSlip: ≤ 0.5 mmAdhesive strength after:• 28 days: ≥ 1.20 N/mm2• heating in +70ºC: ≥ 1.20 N/mm2• immersion in water: ≥ 1.00 N/mm2• 25 freeze-thaw cycles: ≥ 1.10 N/mm2Temperature resistance: from -300ºC to +900ºCAll measurements were conducted according to EN 12004.Directions for use1. Substrate preparationThe surface to be overlaid must be clean, free of dust, grease, paint, loose material etc.Dampening of the substrate before application is recommended.2. ApplicationISOMAT AK 16 is gradually added into water under continuous stirring, until a uniform pasteis formed. A low revolution mixer is recommended for mixing. The mixture should be left about 10 minutes tosettle and should be stirred slightly again. The tile adhesive should be spread (“combed”) onthe substrate using a notched trowel, in order to be uniformly applied on the whole surface.The tiles should be fixed by pressing them in the desired position. The applied mixture must be covered with tileswithin 30 minutes in order to avoid “skin” formation, i.e. before the adhesive film starts setting.ElastificationFor tiling on unstable substrates subject to vibrations or contraction-expansion effects,such as gypsum boards, chipboards, in-floor heating floors, terraces, balconies etc. it isnecessary that the tile adhesive be elastified with the addition of 5-10 kg of ADIFLEX-B to25 kg of ISOMAT AK 16 plus a quantity of water depending on the desired workability.Consumption1.5-4.0 kg/m2, depending on the trowel’s notch size and the nature of the substrate.
ISOMAT MULTIFILL ELASTIC COLORED TILE JOINING MASTIC 280ML WHITE
Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
ISOMAT MULTIFILL ELASTIC COLORED TILE JOINING MASTIC 280ML LIGHT GREY
Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
ISOMAT MULTIFILL ELASTIC COLORED TILE JOINING MASTIC 280ML GREY
Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
PARALIMNITKO CEMENT BASED ACRYLIC TILE ADHESIVE ALFACOL 15* 25KG GRAY
Specifications: EN 12004 C2TE-S2Description: High performance cement-based acrylic tile adhesive,with extended open time and no vertical slip. Exhibits high elasticity, excellent adhesion on all substrates, resistance to constant moisture, to frost and intense substrate movements.Applications: Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, on cementitious renders, cementitious screeds and concrete.Product Identity Appearance: cement-based powder Storage: 9 months in the original packaging, in a dry place Particle size: 0-0.8mm Grouting: 24 h * * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate. Adhesion Strength≥ 1 Ν/mm2 according ΕΝ 12004 1 Ν/mm2 30 min open time 3.1 Ν/mm2 after 28 days 2.1 Ν/mm2 after water immersion 2.7 Ν/mm2 after heat ageing 2.5 Ν/mm2 after freeze/thaw cycles Slip 0.2 mm Deformability: 5.8mmTemperature when in use: -30ºC-+90ºC ApplicationWith the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. The open time of ALFAKOL 15* is 30 minutes. Install the tiles within this period, in order to avoid skin formation. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. Substrates Preparation Substrates must be mechanically sound, free of loose particles, grease, oil or other materials that reduce the adhesion. Dampening of the substrate before application is recommended. The substrate must be stable without cracks and have already completed the curing period of hygrometric shrinkage. Uneven sections must be corrected with suitable smoothing and finishing product. Preparing the mix Gradually pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength.
PARALIMNITIKO CEMENTILIOUS ADHESIVE ALFAKOL 2″ 25KG GRAY
Specifications: EN 12004 C1TEDescription: Cementitious adhesive, with extended open time and no vertical slip. Range of Application: Suitable for all ceramic and porcelain tiles for indoor use, on floor and walls. Also ideal for building YTONG blocks.Product Identity Appearance: cement-based powder Storage: 9 months in the original packaging, in a dry place Particle size: 0-0.8mm Application Data * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate. Adhesion Strength≥ 0.5 Ν/mm2 according 12004 0.5 Ν/mm2 30 min open time 0.9 Ν/mm2 after 28 days 0.5 Ν/mm2 after water immersion 0.6 Ν/mm2 after heat ageing 0.7 Ν/mm2 after freeze/thaw cycles Slip 0.5 mm Temperature: -30ºC – +90ºCApplicationWith the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. Spread as much adhesive as can be covered with tiles in 25-30 minutes. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar.Substrates Preparation All surfaces must be flat, structurally sound, free from dust, oil, grease and any other loose or contaminating materials. To avoid immediate absorption of mix water by the substrate and for better adhesion saturate the surface to provide a saturated surface dry condition. Preparing the mix- Application Pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength
ISOMAT ASPHALTOS COLD APPLICATION MIXTURE 25KG
Ready-to-use cold mix asphalt mix, for local repairs of asphalt or concrete pavements. It is characterized by great flexibility without the appearance of cracks, has very good adhesion to the substrate and has great resistance to weathering and time.
MERCOLA ISOMIX FIBRODUR 900G 6MM
ISOMIX FIBRODUR consists of polypropylene fibers. They are produced from pure polypropylene with hydrophilic surface processing, special additives and in suitable dimensions so that they can be easily dispersed in cementitious mixtures improving plastic properties and workability.ADVANTAGES Crack preventions – reduction caused by contraction and shrinkage during the initial curing period of concrete applicationImprovement of flexural, bending, tensile, impact strength as well as cracking and deteriorationImprovement of weather, soiling and temperature effectsProtection against carbonisation of concreteImprovement of homogeneity, coagulation and coherence, reducing segregation and separation thus increasing compactionImproved chemical, acid, alkali and salt resistanceDoes not offer resistance to chlorinated hydrocarbon solvents over 60oCEasy flow through pumps and spraying equipmentAPPLICATIONSISOMIX FIBRODUR fibers have an extended application range such as:Floors (industrial, stamped, cement paving slabs, concrete stepping slabs, concrete floor heating etc) building and repair mortarsPrefabricated concrete construction elements such as covings, lintels, paving elements, concrete fencing elements etcWater tanks, swimming pools, silos, piping, irrigation channels etcSpray concrete (GUNITE)Asphalt and plumbing ways