HOTLINE

Phone: (+357) 24823938

PARALIMNITIKO CEMENTILIOUS ACRYLIC DEFORMABLE ADHESIVE FOR TILES ALFAKOL 6* 25KG

/

Specifications: EN 12004 C2TE-S1

Description: High performance, deformable, cementitious, acrylic adhesive for tiles,with extended open time and no vertical slip.

Applications: Suitable fori nterior and exterior bonding of every type and size ceramic and porcelain tiles, on floor and walls.

Product Identity

Appearance: cement-based powder

Storage: 9 months in the original packaging, in a dry place
Particle size: 0-0.8mm

Grouting: 24 h * * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate.
Adhesion Strength

≥ 1 Ν/mm2 according ΕΝ 12004

0.8 Ν/mm2 30 min open time
2.1 Ν/mm2 after 28 days
1.5 Ν/mm2 after water immersion
1.9 Ν/mm2 after heat ageing
2.0 Ν/mm2 after freeze/thaw cycles
Slip 0.3 mm
Deformability: 3.3 mm
Temperature when in use: -30ºC-+90ºC

Application
With the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile.

Spread as much adhesive as can be covered with tiles in 25-30 minutes. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar.

Substrates Preparation

Substrates must be mechanically sound, free of loose particles, grease, oil or other materials that reduce the adhesion.
The substrate must be stable without cracks and have already completed the curing period of hygrometric shrinkage. Uneven sections must be corrected with suitable smoothing and finishing product.
Preparing the mix- Application

Pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength.

The open time of ALFAKOL 6*, in normal conditions of temperature and humidity is 30 minutes. Unfavourable environmental conditions (strong sunlight, drying wind, high temperature as well as highly absorbent substrate), could drastically reduce this time to a few minutes.

PARALIMNITIKO CEMENTILIOUS ACRYLIC ADHESIVE FOR TILES ALFAKOL 3*

/

Specifications: EN 12004 C2TE

Description: High performance, cementitious, acrylic adhesive for tiles,with extended open time and no vertical slip.

Range of Application: Suitable for all types of small sized ceramic and porcelain tiles for interior and exterior floor and wall applications.

Product Identity

Appearance: cement-based powder

Storage: 9 months in the original packaging, in a dry place
Particle size: 0-0.8mm

Grouting: 24 h * * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate.


Adhesion Strength

≥ 1 Ν/mm2 according ΕΝ 12004

0.6 Ν/mm2 30 min open time
2.1 Ν/mm2 after 28 days
1 Ν/mm2 after water immersion
1.2 Ν/mm2 after heat ageing
1.1 Ν/mm2 after freeze/thaw cycles
Slip 0.5 mm
Temperature: -30ºC +90ºC

Application

With the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile.
Spread as much adhesive as can be covered with tiles in 25-30 minutes.

Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar.

The open time of ALFAKOL 3*, in normal conditions of temperature and humidity is 30 minutes. Unfavourable environmental conditions (strong sunlight, drying wind, high temperature as well as highly absorbent substrate), could drastically reduce this time to a few minutes.

Substrates Preparation

Substrates must be compact, free from substances that reduce adhesion such as dust, oil, grease and with no loose material.
The substrate must be stable, non-deformable, without cracks and have already completed the curing period of hygrometric shrinkage. Uneven sections must be corrected with suitable smoothing and finishing product.
Preparing the mix- Application

Pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength.

WATERPROOF SELF LEVELING ACRYLIC FLOOR SELF LEVELING COMPOUND 25KG

/

Ready high quality, cementitious self-leveling mortar, one component. Suitable for application from 5 – 30 mm in one layer.

PROPERTIES
Excellent workability and rheology
Easy application by hand or with a pump
Excellent adhesion
High mechanical strength
Smooth and perfectly flat surfaces

APPLICATIONS
Smoothing and leveling of new or existing irregular substrates of concrete, cement mortar or ceramic tiles, in order to form floors with high mechanical strength, suitable for heavy pedestrian traffic in department stores or vehicle traffic in warehouses and parking lots.
Suitable for industrial floors and floor leveling before applying carpets or parquet.
Replaces cement mortar in case of underfloor heating.
The floor from SELF LEVELING COMPOUND can be left as it is or it can accept ceramic or carpet etc. In the first case it is necessary to apply a protective layer of primer, 3-4 days after the application of the mixture, to reduce the absorbency of the floor. In the second case, just apply the appropriate glue for each application.

POLYPROPYLENE FIBERS 600G

/

Reduction of cracks in concrete
Available in 600 gr water-soluble cardboard
Dosage: A package of 600 gr per m³ of concrete
Suitable for adding to coatings (type 12 mm) and Screed WD (type 12 mm, 18 mm)

KNAUF COARSE SPATULA COARSE WHITE

/

The Knauf coarse spatula is a cementitious mortar reinforced with acrylic mixtures. It is ideal for plastering, plasters and exposed concrete indoors or outdoors, to cover and correct imperfections and defects in the application surfaces. Can be applied to masonry and plasterboard ceilings, exposed concrete and plasterboard
• Mixing: 2 liters of water per 5 kg bag
• Yield: 1.5 kg / m2, depending on the type and level of the substrate and the desired final finish.
• Storage – Shelf life: In a dry dry place, on pallets, at temperatures from 5 ° C to 40 ° C, for 6 months from the date of production.

FLASHELASTIC SPA THICK GRANULATED WHITE

/

Reinforced cement spatula for indoor / outdoor use.
Complies with European Standards CE MARKING CYS EN 998-1.

PROPERTIES
Ready to use
It is easily homogenized, without lumps
Excellent adhesion
It is easily rubbed
It does not shrink

APPLICATIONS
Suitable for final finishing on surfaces of 2 o or 3 o hand plaster, painted or not, fairface concrete and plasterboard, indoor / outdoor cement boards.

PARALIMNITIKO WALL LEVELING COMPOUND FLASH SPA FINE WHITE

/

Product Identity Appearance:


White cement-based powder. Packaging: Bags of 10kg & 25 kg Particle size: 0-100μm


Storage: 8 months in the original packaging and in a dry place Application Data Mixing Ratio: 5kg in 1.5-2.5L water Pot life: 4 hours/remix every 1 hour at 23ºC and 50% RH.


Thickness: 1mm/coat Consumption: 2 kg/m2 depending on surface Application temperature: +5 ºC – +35 ºC


Final Performance: Adhesion strength: 0.3 Ν/mm2 – FP:B Bending Strength: 1.9 N/mm2


Compressive strength: CSIII Water absorption: W1

PARALIMNITIKO WALL LEVELING COMPOUND FLASH SPA COARSE WHITE

/

Product Identity

Appearance-color: cement-based white powder
Packaging: 10 kg and 25 kg bags
Particle size: 0-300μm
Storage: 8 months in the original packaging and in a dry place

Application Data

Mixing Ratio: 25kg in 8-10L water
Pot life: 4 hours/remix every 1 hour at 23 oC and 50% RH
Thickness: 1-2mm/coat
Consumption: 2kg/m2 depending on surface
Application temperature: +5 ºC – +35 ºC

Final Performance

Adhesion strength: 0.3 Ν/mm2– FP:B
Bending Strength: 2.4 N/mm2
Compressive strength: 5 N/mm²- CSIII
Water absorption: W0

ELASTOMER CEMENT GROUT PGP BETON FILLER GRAY

/

PGP BETON FILLER is a ready-to-use elastic concrete filler reinforced with ceramic microspheres ideal for filling cracks and joints. It does not crack or shrink due to its composition based on PVA acrylic and ceramic microspheres. Withstands surface movements and vibrations. It rubs easily and has thermal insulating properties. Its gray color blends with cementitious substrates. It can be applied to concrete, plaster, plasterboard, brick, stone, render and wood.

Shopping Cart