Happy Color PERLATO is the pearly “glitters” based glossy paint which gives multicoloured light reflections to the most imaginative decorations.Ideal for decorating “mountain bikes”, mopeds, helmets, masks, frames, decorations, ornaments, friezes, etc.Happy Color PERLATO dries to the touch in 15 minutes and dries fully in 45 minutes.It is suitable for: metal, plastic, wood, glass, ceramics, terracotta, cement and plaster surfaces.
Happy Color HIGH TEMPERATURE is a high quality enamel, with a modified silicone resin base, which allows you to refurbish all surfaces normally subject to high temperatures. Heat resistant up to 350°C. Useful for: varnishing of parts of stoves, fireplaces, hot-water heaters, ovens, chimney flues, barbecues, fire screens, motorcycle mufflers, etc., not exposed to direct contact with flame. Important: to obtain an optimal and long-lasting result it is necessary for the parts varnished with Happy Color ALTE TEMPERATURE to be exposed, even if only once, to a temperature of at least 150°C; any less and the hardening and adhesion of the enamel will only be partial. For particularly tough jobs, such as the varnishing of exhaust manifolds, blast furnaces, professional ovens, etc., the use of Saratoga TOCCO HIGH TEMPERATURE, capable of withstanding temperatures up to 800°C, is recommended. Instructions for use: thoroughly clean the surface of grease, dust, water, etc.Shake well. Once you hear the sound of the marbles inside the cylinder, continue shaking for another minute. Apply the product with very light passes, holding the cylinder about 30 cm from the surface. For best results apply a second coat.Varnish removal: with Acetone and/or Nitre Diluent.Comes with self-cleaning valve.
High quality metallic paint in spray for multiple applications.For decorative applications and general use. With triple grinding treatment compared to single-chip simple sprays, it offers impeccable homogenization and impressive finish.With 4 times more pigments that give impressive coverage with a single hand and without the use of a star.Satin effect. It does not leave fingers and blackness when we touch it.Suitable for use on most surfaces: metal, glass, ceramic and most plastic.After the application do not rub or scratch the surface. Excellent coverage and resistance to UV rays.Internal / External use.Color: Silver metallic with glitter.Packaging: 400ml.
Happy Color ACRYLIC is a bright enamel for interiors and exteriors with a thousand applications.It dries to the touch in 15 minutes and dries fully in 45 minutes. It is suitable for: wood surfaces, metal, glass, ceramic, plastering, masonite, doors, chairs, furniture, frames, knick-knacks,radiators and a thousand other objects. Instructions: carefully clean the surface of grease, dust, water, etc. Shake the spray can energetically for a minute, upside-down.Spray at a distance of 20/30 cm with a slow and constant horizontal movement; after about a minute, pass over the area with a vertical movement.To avoid dripping it is preferable to spray in several thin coats.Varnish Removal: with Acetone and/or a Niter Diluent (thinner).Comes with a self-cleaning valve.APPLICATION FIELDSSaratoga Acrylic Happy Color is especially indicated for varnishing doors, chairs, furniture, frames, ornaments, radiators, wheel rims and a lot of other objects.APPLICATION• All surfaces must be dust free, clean, dry and degreased.• Shake can for a long time, until hearing for a minute the sound of the marbles inside the can.• Keeping the can 30 cm from the surface to treat, apply with slight coats. For a better result, cross horizontal coats with vertical ones.• With self-cleaning valve: when finished, clean the valve turning around the can and pressing till comes out only the gas from the can, without any varnish.For a better result, sand the part to treat with thin sandpaper (wet n° 400)Clean varnish with Acetone and/or Nitro Diluent.It is recommended to use the can at 20°C or bringing its temperature to 20°C before applying.With childproof patented safety cap and colour reference token on cap.STORAGE AND SHELF LIFEIn unopened original packaging, between +20 and +25°C its shelf life is 24 months since manufacturing date. In any case, temperature must be over 5°C andkeep out of sunlight.
COLOR TRANSPARENTFor coloring liquid glass, polyester & polyurethane materialsShake well before useSpecial transparent dye for coloring LIQUID GLASS liquid glass, polyester and polyurethane materials.Instructions for use:Add a few drops to component A (Resin).1-3 drops may be enough for coloring 50gr.Mix well with a clean tongue press until the pigment is completely homogenous, paying special attention to the bottom and the walls of the container.Add component B (Hardener) and mix well.Beware a large amount of pigment can prevent the glass from coagulating.SHADES 30ml:Yellow – Orange – Red – Blue – Green – Black – Magenta – TurquoiseADVANTAGESEasy applicationCreating many shadesColor stabilityExcellent resistance to frequent washing and air pollution
Transparent 2 component epoxy resin, ideal for making special decorative – artistic applicationsLIQUID GLASS is a tough, transparent two-component epoxy resin, which offers great resistance to temperature, humidity and solvents. It is ideal for impregnation, molding and clear casting dissimilar materials and ornaments without shrinking. It is ideal for making special decorative – artistic applications with sculptured objects, by filling voids and pores and forming a final glass-like surface. Use LIQUID GLASS to create fantastic artistic constructions for decoration and use.ADVANTAGESTransparentExcellent adhesion and bonding strengthExcellent mechanical propertiesExcellent water and moisture resistanceHigh temperature resistanceHigh resistance to most chemicalsCan be colored with the transparent SWAN COLORMIX LIQUID GLASS colorantsAPPLICATIONSThousands of applications can be made with any idea and most materials. Tabletops, bowls, serving platters, stools, 3-D displays with leaves and flowers dried or pressed, shells, insects, pebble stones, mineral stones, souvenirs, jewelry, photographs, coins, seeds, peas, beans, pasta, spices, decorative wood constructions and much more.Transparent floor coatings with decorative elements such as pebbles, coins, and many other items.LIQUID GLASS Is ideal for protection and decoration of many surfaces such as wood, metal, stone, ceramics, porcelain, cardboard, etc.Use your imagination, internet and You Tube for ideas and application methods.Coverage: 1kg/m2/mm layer thickness Thinning: no Application: by knifeTouch dry: 6 – 12 hours 20°C Hard dry: 4 – 7 days 20°CInterior use Application temperature: 10-35°CCleaning: with nitro solventYou must pay close attention to the quantity and the way of mixing the 2 components. Danger of high temperatures due to exothermic reaction.All surfaces must be dry and clean from dust and grease.Make sure that the materials used for stirring and the dosing and stirring containers are free of moisture. In difficult cases the use of a dehumidifier will help.Using a spatula, mix well amounts of LIQUID GLASS Α and hardener Β at a ratio of 100:60 respectively.It is advisable to use dosing containers or a precision scale.Stir 2 components with a spatula. Never use an electric drill.Mix small quantities each time since the mixture will start hardening rapidly. The larger the quantity mixed and the higher the temperature, the faster the rate of acceleration of the curing due to the exothermic reaction. At temperatures higher than 25°C and with quantities mixed larger than 500gr one should spread the mix within 5 – 10 minutes or 15-20 minutes for lower temperatures, always monitoring the temperature of the mix.If you apply the material in layers make sure that each layer is applied after basic curing of the previous layer. Alternatively you can apply multiple layers after curing of the previous layer to avoid line creation and reduced transparency.If you are using a mould, spray evenly with MINOS SILICONE SPRAY before pouring the mixture to avoid sticking. For moulding purposes one can use melamine surfaces sprayed with silicone, or polyethylene / polypropylene materials (self-adhesive tapes , nylon sheets etcApply the material into the mould making sure that there is no leak.During curing one should avoid dust, high temperatures and very importantly high humidity.If you are using LIQUID GLASS as a varnish spread material with a spatula.Any bubbles can be removed using a needleInitial curing takes 4 – 6 hours, and final curing is achieved in 4 – 7 days depending on layer thickness and room temperature.Following full curing one can machine – sand the cured object using different grades of sand paper from coarse to fine which will lead to a glass like finish for the sanded areas.CAUTIONHumidity affects the chemical process resulting in bubbles. Special care should be paid to applications with wood where it is difficult to measure humidity.It is not suitable for exposure to sunlight (UV) although the material presents one of the best UV resistance from most similar products.Lightweight objects must be fastened (secured to their intended position ) to avoid floating or moving until final curing.Mixing of large quantities and high temperatures rapidly accelerate curing due to exothermic reaction which can lead to bubble formation and discoloration.In case of severe overheating with possible smoke release, spray the surface with water to lower the temperature.Close lids firmly after use and do not change lids between containers.All tests should be carried out before final application in order to ensure the compatibility of the materials to be bonded.Suitable for use by professionals or experienced users.Please contact our technical support for any technical assistance.COLOURING LIQUID GLASSYou can colour LIQUID GLASS with the transparent colorants SWAN COLORMIX LIQUID GLASS which allow you to ‘see through’ the cast piece. The dyes are very concentrated. 2-3 drops might be enough for 50gr of final product.INSTRUCTION FOR USEAdd just a few drops of colorant in component A (resin). Stir well to blend using a tongue depressor. Special attention must be given to the bottom and sides of the container. Add part B (hardener) and mix well.Caution: Too much colorant will inhibit the cure of the resin. Colorants may be used to color an entire casting or can be used in the final layer to create a background. Keep in mind that colored resin in your mixing container will look much darker than when poured into a thinner area.CLEANINGTools and adhesive residues should be cleaned right after use with nitro solvent. After the material has hardened it can be removed using Mercola STRIPP & CLEAN paint stripper.
Direct application on furniture, benches, worktops and cabinets.High resistance to bumps and scratches.
Water based Hybrid primer ideal before applying ISOLOR Hybrid Aqua Plus elastomericwaterproofing coating. Low odor and VOC. Ready for use.Suitable for the priming of new cement substrates as also of existing waterproofing coatings.Can be applied above bituminous materials, mosaic, aluminium foils etc.Excellent adhesion and penetration. Quick drying.TECHNICAL CHARACTERISTICSSpecific gravity: 0,99 -1,03g/lCovering power: 4-8m2/lt per coat depending on the substrate.Dilution: Ready for use.Drying: Touch dry after ½–1 hour.VOC class: “Binding primers”. Type WB. VOC limit=30gr/lt. Max VOC of product ready for use=5gr/lt.Recoatability: Recoatable after 2-3 hours. These times prolong under cold and wet conditions.Color shades: Milky-transparentAPPLICATION EQUIPMENT: Brush, roller and airless spray.SURFACE PREPARATIONClean the surface from oil, cropped paints, dust, dampness and moulds.APPLICATIONStir well before use. Apply uniformly. Recoatable with ISOLOR Hybrid or water based proofingcoatings.CLEANING EQUIPMENTKeep the tools wet during application. Strain well your tools from paint back to the pot andclean immediately with water and soap.APPLICATION CONDITIONSTemperature 8-30°C and relative humidity lower than 80%. Contrary weather conditions maydegrade product’s quality. New concretes or masonry should be dried for a period of 3-4 weeksbefore priming. Don’t prime high humid substrates before drying.STORAGE CONDITIONSClose well after use. Store in a cool place. Protect from freezing and sun exposure.PRECAUTIONARY STATEMENTKeep out of reach of children.
Form: Acrylic-polyurethane.Properties: Easy application with great coverage, excellent adhesion, particularly resistant to adverse weather conditions, high elasticity and does not crack.Applications: Ideal for waterproofing roofs.Mixing ratio with water: Ready to use.
Water based high solids hybrid elastomeric waterproofing coating with high tech acrylic and polyurethane resins. Fast curing and water tight againstponding water. Ιt develops a water vapour diffusive coating, which keeps its elasticity from -20°C up to +80°C and is non-sticky, walkable and resistant to pedestrian traffic. Excellent crack bridging ability up to 1,5mm.Its innovative synthesis permits high build coating even in one coat (1,5kg/m2), very good dirty pick up resistance and superior thermoreflectiveproperties. It is certified as cool-thermoreflective coating.Reliable and cost-effective water proofing solution. Easy to apply.ISOLOR HYBRID AQUA plus carries the CE mark as it is certified by EN-1504-2 as a concrete protection product against penetration, moisture control and increased resistance to limiting the moisture content.It is also certified as cold – reflective material (CRES, DEMOKRITOS) and offers excellent heat – refraction (reducing the cooling cost in the summer months).It is a solution of excellent cost-effectiveness in sealing maintenance with or without the use of glass or polyester reinforcement strips. Easy application and maintenance (by qualified or unskilled personnel), user friendly and environment friendlySpecific Gravity 1,50-1,54 kg/ltCovering Power and Consumption 1, 25-2 m2 /kg & 0,5-0,8 m2 /kg (roller application) per coat and 0,7-1 m2 /kg & 1- 1,5kg/m2 (thick brush application) depending onsurface roughnessDilution Up to 5% on volume with water. For application on old bituminous roofing, the first coat should be diluted up to 10%.Drying 1-3 hours touch free. Recoat able 8-12 hours.Recoatability 6-12 hours after first layer’s application These times prolong undercold and wet weather conditions. Walkable after 3-4 hours.Water & Alkali resistance Very good water and alkali resistance.Elasticity & Elongation at break 350% elongation, film thickness up to 1mm and temperature 23°C&. 100% elongation, film thickness up to 1mm and temperature 10°C & Keeps elasticity on temperatures between –20°C and 80°C.VOC Class “Exterior wall coatings of mineral substrate”. Type WB. VOC limit=40 gr/lt. Max VOC of product ready for use = 39 gr/lt. VOC: organicvolatile compounds wit boiling point < 250°C.Application tools Brush, Roller, Airless SprayShades White, Red-brown.Reflection in visible spectrum R= 89,5% ±2% (400-750 nm, ASTM E903-96)Reflection in Infra-Rede (IR) area R=89,5% ± 2% (780‐2500 nm, ASTM E903‐96)Emission Coefficient 0,88 (ε, ASTM E408‐71)Adhesion on concrete >4MPa (EN 24624)Adhesion on concrete on which Isolor Hybrid Primer has been applied >6MPa (EN 24624)Tensile Strengh ( 23°C /-20°C) N/mm² = 1.4 / 7.5SURFACE PREPARATIONNew surfaces: apply Isolor Hybrid Primer, which is ready for usewithout delusion. Old surfaces: Clean the surface of dust, oil,cropped paints, rust and dampness. If needed use repair productslike Smaltofill elastic putty and/or polyester reinforcement material and/or PU shielding products. Then apply Isolor Hybrid Primer.APPLICATIONStir well. Apply uniformly ISOLOR Hybrid Aqua Plus. Higher consumption of the product per m2 affects the lifetime expectancy ofthe coating. The use of polyester reinforcementmaterial needs for the application three coats of ISOLOR HybridAqua Plus+. Put the reinforcement material on the wet first coat.After the drying, apply additional two coats.CLEANING EQUIPMENTWhile working keep your equipment wet, either in the pot, or inthe paint lauder. Strain well your tools from paint back to the potand clean immediately with warm water and soap.APPLICATION CONDITIONSTemperature 8-350C and relative humidity lower than 80%. Do not apply in case of imminent rain.STORAGEClose well after application. Store in a cool place. Protect from freezing and sun exposure.
