HOTLINE

Phone: (+357) 24823938

RUSTOLEUM COMBICOLOR ORIGINAL SMOOTH ANTI-RUST PRIMER AND TOPCOAT

/

Anti-rust primer and topcoat in one, based on alkyd resins for direct application onto rust.

Long lifetime
Maximum elasticity
Direct application onto rust
Low odour
Excellent anti-corrosion protection
Excellent one-coat cover Resistant to knocks

Coverage:10.5m²/L
Drying Time:2 hours
Time Between Coats:8-16 hours
Use:INTERIOR & EXTERIOR
Application Method:ROLLER, BRUSH, SPRAY
Thinner:THINNER 7301 (COMBICOLOR)

RUST-OLEUM® CombiColor Metal 7300/7400 coating is primer and topcoat in one, based on
a urethane modified alkyd, providing good drying properties at low temperatures.
The product contains rust-inhibitive pigments and is lead- and chromate free.

RECOMMENDED USES
RUST-OLEUM CombiColor Metal 7300/7400 should be applied on bare, manually derusted or
with CombiPrimer Anti-Corrosion 3369/3380 primed steel. CombiColor Metal is intended for
brush and roller application and can also be applied by air spray.
RUST-OLEUM CombiColor Metal 7300/7400 offers corrosion protection in a light industrial
environment.
For metal structures in a more aggressive industrial environment, prior application of a RUSTOLEUM CombiPrimer Anti-Corrosion 3369/3380 is recommended.

TECHNICAL DATA
Appearance: High gloss, Satin (black and white), Flat (black and white).
Colour: See colour card.
Satin and High gloss are also available as tint base.
Density: High gloss/flat: 1.07 kg/l. ± 0.09 depending on colour
Satin: 1,22 kg/l. ± 0,10 depending on colour
Solids Content: High gloss/flat: 54.6% by volume ± 2.0 depending on colour
Satin: 50,6 volume % ± 2,0 depending on colour
Viscosity: High gloss/flat: 100 – 104 KU / Krebs Stormer Units at 20°C
Satin: 86 – 91 KU /Krebs Stormer Units bij 20°C
Recommended film thickness: 55 µm dry, equals 100 µm wet
VOC-content: 439 g/l max.
Ready-to-use mixture: 495 g/l max.
Category: A/i
EU Limit values: 600g/l (2007) / 500g/l (2010)

Coverage
Theoretical: 10.3m²/l at 55µm dry, depending on colour.
Practical: Practical coverage depends on many factors such as porosity and
roughness of the substrate and material losses during application.

SURFACE PREPARATION
Remove oil, grease and all other surface contaminations by alkaline or high pressure (steam)
cleaning in combination with appropriate detergents. Remove rust scale, loose mill scale,
loose rust and loose coatings by scraping and wire brushing to St 3 (ISO 8501-1 : 1988), light
blast cleaning or sanding. Sand intact coatings to roughen the surface slightly.
The surface must be clean and dry during application. Galvanised, Zinc and Alu

RUSTOLEUM COMBICOLOR HAMMERTONE ANTI-RUST PRIMER AND TOPCOAT

/

Anti-rust primer and topcoat in one, based on alkyd resins for direct application onto rust.

Long lifetime
Maximum elasticity
Low odour
Excellent anti-corrosion protection
Excellent one-coat cover
Resistant to knocks

Coverage:10.5m²/L

Drying Time:2 hours

Time Between Coats:8-16 hours

Use:INTERIOR & EXTERIOR

Application Method:ROLLER, BRUSH, SPRAY

Thinner:THINNER 7302 (COMBICOLOR)

RECOMMENDED USES
CombiColor Hammertone 7300 can be applied directly on bare, manually derusted or with
CombiPrimer Anti-Corrosion 3369/3380 primed steel.
CombiColor Hammertone 7300 is intended for brush and roller application and can also be
applied by air spray.
On properly primed or previously coated surfaces CombiColor Hammertone 7300 offers
corrosion protection in a light industrial environment.
For metal structures in a more aggressive industrial environment, application of an additional
CombiPrimer Anti-Corrosion 3369/3380 is recommended or a second coat of
CombiColor Hammertone 7300 can be applied.

Coverage
Theoretical: 8.0 – 8.5 m²/l, depending on colour.
Practical: Practical coverage depends on many factors such as porosity and
roughness of the substrate and material losses during application.

SURFACE PREPARATION
Remove oil, grease and all other contamination by alkaline or high pressure (steam) cleaning
in combination with appropriate detergents.
Remove rust scale, loose mill scale, loose rust and loose coatings by scraping and wire
brushing to St3 (ISO 8501-1: 1988), light blast cleaning or sanding, followed by priming with
the recommended CombiPrimer Anti-Corrosion 3369/3380.
Sand previous coatings in good condition to provide a key for adhesion and check
compatibility. The surface must be clean and dry during application.
Galvanised, Zinc and Aluminium surfaces have to be primed first with CombiPrimer Tack Coat
3302.

DIRECTION FOR USE
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
APPLICATION & THINNING
Brush: Up to 10 vol. % with 7301.
Use natural bristles, long hair flat brushes for optimal hammertone
appearance.

Roller: Up to 10 vol. % with 7301.
Use short nap poly-amide (Perlon 6 – 12 mm) rollers.

Air-atomised spray: 10-25 vol.% Rust-Oleum Thinner 7302.
Gravity cup and pressure cup.
Tip size: 1.0 – 1.5 mm. Atomising pressure 2 – 4 bar.

Cleanup: Use Rust-Oleum Thinner 7301 or mineral spirits.

APPLICATION CONDITIONS
Temperature of air, substrate and coating material between 10 and 35°C, relative humidity
below 85%. The substrate temperature must be at least 3°C above dew point.

REMARKS
Brushes, rollers and cleaning solvents should only be used for hammertone application.

SAFETY
Consult Safety Data Sheet and Safety Information printed on the can.

SHELLIFE / STORAGE CONDITIONS
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in
direct sunlight at temperatures between 5° and 35°C.

ISOMAT ISOLAC RUST PRIMER FOR METAL SURFACES

/

Anti-rust primer for metal surfaces. It is suitable for both indoor and outdoor use.
It offers excellent adhesion and efficiently protects metal surfaces from rust.

Fields of application

It is used οn new or old metal surfaces such as doors, railings, machinery and tools and
constitutes the ideal substrate for the enamel paint ISOLAC DUCO.

Directions for use

1. Substrate preparation The metal surface should be dry and free of rust,
grease, loose particles or paint, dust, etc., while any imperfections should be rubbed with
sandpaper.

2. Application
Apply ISOLAC RUST PRIMER in one or two layers, thinned with 5-10% SM-18 for application
by brush or roller, and with 10-20% SM-16 for airless spray application.The second coat is
applied after the first coat has completely dried, approximately after 8 hours. After the second coat
has dried, it can be smoothed with sandpaper for better adhesion of the final paint. Temperature
during application and drying of the primer should be between +10°C and +35°C.


Coverage
ISOLAC RUST PRIMER covers up to 13m²/l, on previously prepared surfaces.

VECHRO CORROLUX HAMMERED ENAMEL PAINT

/

Special paint for industrial use, suitable either for protection or for decoration of metallic surfaces, machines, electric equipment etc.

It gives a hammered surface and very good decoration results at the same time covers any defect on the surface.

It creates tough film with excellent adhesion οn metallic surfaces such as steel, aluminum and galvanized.

Dries fast and gives excellent mechanic resistance.

VECHRO POOL PLUS ONE PAINT FOR SWIMMING POOLS

/

VECHRO POOL PLUS ONE is a high quality paint suitable for swimming pools, based on chlorinated rubber resin, which creates a tough and elastic film.

It is proposed for the painting of both new or repainted swimming pools made by concrete. Has great adhesion on these surfaces.

It doesn’t contain lead or other toxic substances and doesn’t pollute water, towards which has great and permanent resistance.

It is recommended for swimming pools or surfaces with permanent touch to fresh water or seawater.

It has excellent resistance to chlorine and other preservative chemicals, which used. Gives excellent decorative results without complicated application.

It is easy to use and apply after the appropriate pretreatment of the substrate.

Very rapid drying even in adverse weather conditions.

VECHRO ACRYLIC ROAD MARKING PAINT

/

VECHRO Acrylic Road Marking Paint.

Color Shades : White , Yellow, Blue, Black. Other Shades upon request.

Covering power : 1-1,4 m2 /lt

Dilution. : Up to 5% on volume with with No 1 thinner of VECHRO for application by brush or roller, for airless spray application use up to 10-15% on volume with No 1 thinner of VECHRO.

Drying : Touch free after 15-17 minutes. Fully dry after 1 hour.

VECHRO DULISOL ACRYLIC PAINT FOR PAVED FLOORS

/

VECHRO Dulisol. Special insulator based on synthetic resins suitable for painting and protection of external surfaces of asvestos cement, concrete and ELLENIT plates, terraces and roof tiles.

It has great alkali and water resistance.

Its synthesis makes it UV resistant and ideal for tough weather conditions.

V33 TRAFFIC EXTREME FLOOR PAINT

/

One-component floor paint for cement, concrete, brick, wood and metal floors, for interior and exterior use.

Very durable, for high traffic areas Resistant to oils, greases, chemicals, etc Abrasion resistant and non-peeling Water and UV resistant

Coverage:12 m²/L
Time Between Coats:24 hours
Drying Time:8 hours
Use:INTERIOR & EXTERIOR
Application Method:ROLLER, BRUSH
Tool Cleaner:WHITE SPIRIT

Shopping Cart