Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
Colored, elastic one-component tile jointing mastic. Suitable for grouting any type of wall or floor tiles, on a variety of surfaces where the requirements for elasticity are particularly high (eg expansion joints, etc.). It is applied indoors or outdoors.
Specifications: EN 12004 C2TE-S2Description: High performance cement-based acrylic tile adhesive,with extended open time and no vertical slip. Exhibits high elasticity, excellent adhesion on all substrates, resistance to constant moisture, to frost and intense substrate movements.Applications: Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, on cementitious renders, cementitious screeds and concrete.Product Identity Appearance: cement-based powder Storage: 9 months in the original packaging, in a dry place Particle size: 0-0.8mm Grouting: 24 h * * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate. Adhesion Strength≥ 1 Ν/mm2 according ΕΝ 12004 1 Ν/mm2 30 min open time 3.1 Ν/mm2 after 28 days 2.1 Ν/mm2 after water immersion 2.7 Ν/mm2 after heat ageing 2.5 Ν/mm2 after freeze/thaw cycles Slip 0.2 mm Deformability: 5.8mmTemperature when in use: -30ºC-+90ºC ApplicationWith the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. The open time of ALFAKOL 15* is 30 minutes. Install the tiles within this period, in order to avoid skin formation. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. Substrates Preparation Substrates must be mechanically sound, free of loose particles, grease, oil or other materials that reduce the adhesion. Dampening of the substrate before application is recommended. The substrate must be stable without cracks and have already completed the curing period of hygrometric shrinkage. Uneven sections must be corrected with suitable smoothing and finishing product. Preparing the mix Gradually pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength.
Specifications: EN 12004 C1TEDescription: Cementitious adhesive, with extended open time and no vertical slip. Range of Application: Suitable for all ceramic and porcelain tiles for indoor use, on floor and walls. Also ideal for building YTONG blocks.Product Identity Appearance: cement-based powder Storage: 9 months in the original packaging, in a dry place Particle size: 0-0.8mm Application Data * The time for grouting or for final use may vary depending on weather conditions, application thickness and the porosity of the substrate. Adhesion Strength≥ 0.5 Ν/mm2 according 12004 0.5 Ν/mm2 30 min open time 0.9 Ν/mm2 after 28 days 0.5 Ν/mm2 after water immersion 0.6 Ν/mm2 after heat ageing 0.7 Ν/mm2 after freeze/thaw cycles Slip 0.5 mm Temperature: -30ºC – +90ºCApplicationWith the flat side of the trowel apply the adhesive to the substrate, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. Spread as much adhesive as can be covered with tiles in 25-30 minutes. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tiles and adjust level. If mortar is skinned over (not sticky), remove and replace with fresh mortar.Substrates Preparation All surfaces must be flat, structurally sound, free from dust, oil, grease and any other loose or contaminating materials. To avoid immediate absorption of mix water by the substrate and for better adhesion saturate the surface to provide a saturated surface dry condition. Preparing the mix- Application Pour the material to a bucket of clean water mixing constantly with a low speed (400 rpm) electric mixer until a creamy consistency is achieved. Allow mixture settle for 5 minutes and remix prior the application. Attention! Additional water will make your mixture sloppy and may cause negative results on final strength
Ready-to-use cold mix asphalt mix, for local repairs of asphalt or concrete pavements. It is characterized by great flexibility without the appearance of cracks, has very good adhesion to the substrate and has great resistance to weathering and time.
ISOMIX FIBRODUR consists of polypropylene fibers. They are produced from pure polypropylene with hydrophilic surface processing, special additives and in suitable dimensions so that they can be easily dispersed in cementitious mixtures improving plastic properties and workability.ADVANTAGES Crack preventions – reduction caused by contraction and shrinkage during the initial curing period of concrete applicationImprovement of flexural, bending, tensile, impact strength as well as cracking and deteriorationImprovement of weather, soiling and temperature effectsProtection against carbonisation of concreteImprovement of homogeneity, coagulation and coherence, reducing segregation and separation thus increasing compactionImproved chemical, acid, alkali and salt resistanceDoes not offer resistance to chlorinated hydrocarbon solvents over 60oCEasy flow through pumps and spraying equipmentAPPLICATIONSISOMIX FIBRODUR fibers have an extended application range such as:Floors (industrial, stamped, cement paving slabs, concrete stepping slabs, concrete floor heating etc) building and repair mortarsPrefabricated concrete construction elements such as covings, lintels, paving elements, concrete fencing elements etcWater tanks, swimming pools, silos, piping, irrigation channels etcSpray concrete (GUNITE)Asphalt and plumbing ways
Ecological, lightweight insulating plaster based on expanded perlite, for indoor / outdoor use.Complies with European Specifications CE MARKING CYS EN 998-1 and EN 998-2.PROPERTIESReady to useExcellent workabilityExcellent adhesionHigh strengths APPLICATIONSFor indoor and outdoor use for building bricks 1 by 2 by plastering hand on blocks, bricks insulated and non, Climalite, Ytong, UB200, FairFace ( where primed with medicament) tsimentosova, tsimentopetres and polystyrene (affixed glue with net in polystyrene).
One compenent cementitious mortar based on high quality cement, selected fine grained sand, special additives and fibers. APPLICATIONSSuitable for levelling the existing integrated fiberglass mesh on thermal insulation panels, on cement boards and gypsum boards prior the application of paint.
One-component cement mortar for welding and smoothing of thermal insulation panels and fiberglass.PROPERTIESEasy to applyExcellent adhesionHigh thixotropyIt does not shrinkAPPLICATIONSIdeal for gluing fiberglass to extruded & expanded polystyrene or stone wool and surface sanding, as well as for gluing thermal insulation panels to brick or plaster surface and FairFace concrete.Also suitable for plasterboard and cement boards as a coating, or in existing textured, graphite or painted spray.
