Happy Color RUST PREVENTER undercoating is suitable for protection against corrosion and for varnish prepping for all metals, even alloys.Can be varnished over with any type of enamel and, thanks to its use of acrylic resins, assures above-normal adhesion and longlastingness.
Stain Covering Spray: A specially formulated paint to cover all types of stains located indoors and outdoors. Recommended for stains caused by nicotine, soot, oil, tomato sauce, red wine, wine vinegar, tea, coffee, lipstick, normal or wax crayons, pencils and wateror solvent-based felt-tip pens. Suitable also as a finishing coat to renew and refresh panels and false ceilings in plaster and cardboard. The 360° multi-directional valve sprays the product in all directions with great accuracy, even in difficult-toaccess- areas.It can be overcoated with the same product whenever required and with other products after a minimum of 24-30 hours. Not overcoatable with bi-component paint.
Sanitary Appliance Renewal Spray: A varnish containing special adhesion-promoter resins for painting and renewing ceramic items and sanitary appliances. It is resistant to detergents and hot water (104-122°F/40-50°C) after 5 days from application, and dries rapidly after 15-25 minutes. Wait at least 5 days from the time of application before allowing contact with hot water. It can be overcoated with the same product whenever required and with other products after a minimum of 24-30 hours.Not overcoatable with bicomponent paint.Directions: degrease and dry the surface well. Shake the can for 1-2 minutes before use and spray the surface from a distance of 25-30 cm.Apply the product with light criss-cross movements, moving vertically first and then horizontally.
Ideal for multi surface, this Clear matt matt chalkboard spray paint from the Chalkboard range by Rust-Oleum has been specially designed to give a stunning finish to around your home. Simply apply and leave for 60 minutes to dry-a great way to revamp your home. Covers 5m² per litre on average.Creates a chalkboard on virtually any painted surfaceWorks with conventional chalks and chalk markersQuick drying formulationTough, scratch resistant finish
High quality water based new generation velvet – flat acrylic water-based paint with low VOC. Suitable designed paint for school boards. It provides a surface with excellent resistance toscratching, frequent washing and scrubbing. Erases cleanly.It dries uniformly and quickly.It has great brush ability and give a smooth flat surface. It converts surfaces into a usable chalkboard under the proper preparation.TECHNICAL CHARACTERISTICSTexture Flat <5 degrees at 85º.Specific weight 1,14 – 1,20kg/ltCovering power 11 -13m2/lt per layerDilution Up to 10% on volume with water using brushor roller and max 20% when using spray.Drying 2-3 hours touch free.Recoatability 6 hours after application or after firstlayer’s hardening. These times prolong under cold and wet weather conditions.VOC class “Interior/exterior trim and cladding paints for wood and metal” Type WB. VOC limit =130 gr/lt. Max VOC of product ready foruse= 85 gr/lt. The paint contains also solvents which are not considered as VOC.Shades Black.SURFACE PREPARATIONClean the surface of dust, oil, cropped paints, rust. Sandpaper well. Onnew surfaces it is proposed one coat of SMALTOLUX hydro MASTER PRIMER.APPLICATIONStir well. Apply 1 or 2 coats of Smaltolux Hydro Blackboard.TIPS FOR USE7 days after painting and before writing, condition the surface by rubbingthe side of a piece of a white chalk over the entire surface and erase. This will leave a coat of chalk dust that will provide the best erasability. Chalkboard can be wiped clean with a damp cloth. Wait 10 days after paintingbefore wiping it down. For better result, repeat conditioning step aftercleaning once again. The chalkboard finish is ready for use!CLEANING EQUIPMENTWhile working keep your equipment wet, either in the pot, or in the paintlauder. Strain well your tools from paint back to the pot and clean immediately with water and soap.APPLICATION CONDITIONSTemperature 8-30ºC and relative humidity lower than 80%. Contraryweather conditions may degrade paint’s quality.STORAGEStore in a cool place, protect from freezing and sun exposure. Close thecan well after application to keep in good condition. Recover unused paintfor re-use. Reuse of paint can effectively minimize the product’s life cycleenvironmental impact.
Chalkcolour water-basedultra-matt, velvety hapticvery good adhesion on most surfaceshigh opaque, high colour intensitylightfast, long durability due to colour resin systemvery low VOC-contentfor interieur and exterieur (therefore extra protection varnish)
2-component enamel for porcelain, ceramic tiles, glass and fiberglass in kitchens and bathrooms. Provides excellent adhesion, durability and color retention in high humidity areas.
Permanently colours concrete, mortar, render or screed.Does not effect the performance or durability of any mortar mix.For general use use 1.2kg to 25kg cement.
Special gloss alkyd enamel, with excellent resistance to high temperature. Suitable mainly for radiators. It gives very good adhesion, hardness, fast drying and low yellowing.
FERNOVUS RADIATOR Spray is a shiny, acrylic/silicon-resin base enamel which resists heat up to 120°C. It does not yellow or peel. Can be applied directly onto rusted surfaces. Useful for: radiators, heaters, stovepipes, electric convectors, and all surfaces and objects subjected to heat.Instructions for use: radiators must be turned off and cold. The surfaces are to be clean, dry, degreased and free of any non-adhering dust, grease or paint as well as any crumbling rust. Shake the cylinder well until the sound of the marbles can be heard in the interior, continuing to shake for another minute. FIRST COAT: apply the product in light, criss-crossed passes, holding the cylinder vertically and at a distance of 25-30 cm. For best, more uniform results, shake the cylinder occasionally during use. Optimal cylinder temperature is 20-25°C; do not use at temperatures less than 15°C. Dries to the touch in approximately one hour. SECOND COAT: can take place any time. Wait until the paint has completely hardened, at least 24 hours after application, before subjecting it to heat. Comes with self-cleaning valve.Paint removal: with acetone and/or cellulose thinner.
