HOTLINE

Phone: (+357) 24823938

RUSTOLEUM GALVA ZINC-ALU GALVANIZING PAINT 1KG

/

RUST-OLEUM® Bright Galvanizing 1017 is a fast drying, zinc rich coating based on an epoxy
ester resin. The product contains pure zinc and aluminium as pigments and provides cathodic
protection.

Withstands up to 500 hours or salt spray (DIN 50021 SS)
90% pure zinc in the form of dry film paint
Full protection for pure and galvanized steel
Heat resistant up to 300ºC
Excellent protection against moisture and salt spray

Coverage:11.5m²/L

Drying Time:30 minutes

Application Method:BRUSH

Use:INTERIOR & EXTERIOR

Tool Cleaner:WHITE SPIRIT

RECOMMENDED USES
RUST-OLEUM Bright Galvanizing 1017 should be used on new, bare steel, blasted steel or
galvanized steel surfaces.

RUST-OLEUM Bright Galvanizing 1017 is primarily intended for brush application on small
areas or for touch-up.

RUST-OLEUM Bright Galvanizing 1017 can be recoated with non-saponifiable coatings.

RUST-OLEUM Bright Galvanizing 1017 should be used as a single coat in light industrial
exposures, corrosive environments and high humidity areas.

TECHNICAL DATA
Appearance: Flat
Colour: Aluminium
Density: 1,77 kg/ltr
% zinc/alu: 76% in dry film (67,5% Zn / 8,5% Al)
Solids Contents: 41,8% by volume
Viscosity: 88 – 92 KU /Krebs Stormer Units at 20°C
Recommended film thickness: 35 µm dry, equals 85 µm wet
VOC-content: 477 g/l max.
Ready-to-use mixture: 497 g/l max.
Category: A/i
EU Limit value: 600g/l (2007) / 500g/l (2010)

Coverage
Theoretical: 11,5 m²/l at 35 µm dry
6,5m²/kg at 35 µm dry
Practical: Practical coverage depends on many factors such as porosity and
roughness of the substrate and material losses during application.

SURFACE PREPARATION
Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam)
cleaning in combination with appropriate detergents. For optimum results remove rust, rust
scale, mill scale and deteriorated coatings by abrasive blasting to Sa 2½ (ISO 8501-1 : 1988),
blast profile max. 50 µm. The surface must be clean and dry during application.

DIRECTION FOR USE
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
To avoid settlement of the zinc pigments on the bottom of the can stir regularly during
application.

APPLICATION & THINNING
Brush: Up to 5 vol. %; RUST-OLEUM Thinner 160.
Use natural bristles, longhair brushes.

Cleanup: Use RUST-OLEUM Thinner 160 or aromatic hydrocarbons.

APPLICATION CONDITIONS
Temperature of air, substrate and coating material between 5 and 35°C and relative humidity
below 85%. The substrate temperature must be at least 3°C above dew point.

REMARKS
Maximum dry film thickness per coat: 75 µm dry, equals 180 µm wet.
RUST-OLEUM Bright Galvanizing 1017 should preferably be applied in a maximum dry film
thickness of 35 µm if recoated.

SAFETY
Consult Safety Data Sheet and Safety Information printed on the can.

SHELLIFE / STORAGE CONDITIONS
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in
direct sunlight at temperatures between 5° and 35°C.

V33 VARNISH DECO RAW METALS 500ML

/

Colourless anti-rust, anti-corrosion varnish based on alkyd resin.

Lasting anti-rust protection
Easy application
Resistant to weather conditions
Direct application onto rust
Non-dripping

Time Between Coats:12 hours

Drying Time:2 hours

Coverage:20m²/L

Use:INTERIOR & EXTERIOR

Application Method:ROLLER, BRUSH

Tool Cleaner:WHITE SPIRIT

ECO SERVICE KONVERTER RUST TRANSFORMER 750ML

/

Konverter transforms rust into a stable, black chemical compound
and forms a film that protects all ferrous surfaces: gates, entrance doors, railings, gutters and anything made of iron.

Spread the product with a brush directly on the rust, leave to dry for at least 12/24 hours than overpaint with any type of paint, even long after application.

KONVERTER LIQUID is ready to use and yields about 15 sq.m per litre.

ECO SERVICE ALLUMINIO SPRAY 400ML

/

Aluminium is a spray product with a high aluminum content.

It forms a film which restores and protects all aluminum surfaces.

It can be painted upon or left as a final protection.

Shake sprays products very well before use.

High heat resistance.

RUSTOLEUM COMBICOLOR HAMMERTONE ANTI-RUST PRIMER AND TOPCOAT 750ML LIGHT GREY

/

Anti-rust primer and topcoat in one, based on alkyd resins for direct application onto rust.

Long lifetime
Maximum elasticity
Low odour
Excellent anti-corrosion protection
Excellent one-coat cover
Resistant to knocks

Coverage:10.5m²/L

Drying Time:2 hours

Time Between Coats:8-16 hours

Use:INTERIOR & EXTERIOR

Application Method:ROLLER, BRUSH, SPRAY

Thinner:THINNER 7302 (COMBICOLOR)

RECOMMENDED USES
CombiColor Hammertone 7300 can be applied directly on bare, manually derusted or with
CombiPrimer Anti-Corrosion 3369/3380 primed steel.
CombiColor Hammertone 7300 is intended for brush and roller application and can also be
applied by air spray.
On properly primed or previously coated surfaces CombiColor Hammertone 7300 offers
corrosion protection in a light industrial environment.
For metal structures in a more aggressive industrial environment, application of an additional
CombiPrimer Anti-Corrosion 3369/3380 is recommended or a second coat of
CombiColor Hammertone 7300 can be applied.

Coverage
Theoretical: 8.0 – 8.5 m²/l, depending on colour.
Practical: Practical coverage depends on many factors such as porosity and
roughness of the substrate and material losses during application.

SURFACE PREPARATION
Remove oil, grease and all other contamination by alkaline or high pressure (steam) cleaning
in combination with appropriate detergents.
Remove rust scale, loose mill scale, loose rust and loose coatings by scraping and wire
brushing to St3 (ISO 8501-1: 1988), light blast cleaning or sanding, followed by priming with
the recommended CombiPrimer Anti-Corrosion 3369/3380.
Sand previous coatings in good condition to provide a key for adhesion and check
compatibility. The surface must be clean and dry during application.
Galvanised, Zinc and Aluminium surfaces have to be primed first with CombiPrimer Tack Coat
3302.

DIRECTION FOR USE
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
APPLICATION & THINNING
Brush: Up to 10 vol. % with 7301.
Use natural bristles, long hair flat brushes for optimal hammertone
appearance.

Roller: Up to 10 vol. % with 7301.
Use short nap poly-amide (Perlon 6 – 12 mm) rollers.

Air-atomised spray: 10-25 vol.% Rust-Oleum Thinner 7302.
Gravity cup and pressure cup.
Tip size: 1.0 – 1.5 mm. Atomising pressure 2 – 4 bar.

Cleanup: Use Rust-Oleum Thinner 7301 or mineral spirits.

APPLICATION CONDITIONS
Temperature of air, substrate and coating material between 10 and 35°C, relative humidity
below 85%. The substrate temperature must be at least 3°C above dew point.

REMARKS
Brushes, rollers and cleaning solvents should only be used for hammertone application.

SAFETY
Consult Safety Data Sheet and Safety Information printed on the can.

SHELLIFE / STORAGE CONDITIONS
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in
direct sunlight at temperatures between 5° and 35°C.

SWAN PREMIUM POOL PAINT 2K (A+B) 3KG BLEU

/

PREMIUM POOL PAINT is a high performance 2 component acrylic – urethane paint for swimming pools.
It has excellent adhesion properties, elasticity, hardness and strong resistance to abrasion.
It is highly resistant to sun UV rays, chemicals, water, seawater and suntan oils. Its special acrylic – urethane technology guarantees a durable, long-lasting finish.

ADVANTAGES
Excellent adhesion properties and elasticity
Excellent wear and UV resistance
Excellent durability to water and seawater
Excellent resistance to chemicals
Guarantees a durable, long-lasting finish.

APPLICATIONS
Suitable for painting swimming pools of interior and exterior areas.
Suitable for application on concrete, screeds, stone, metallic and wooden surfaces.

SURFACE PREPARATION
Surfaces should be dry and clean from dust and any oily residues. Dust, oil, humidity or rust seriously affect the coating’s adhesion.
Loose substrates of concrete and screeds are not suitable for painting as the coat will peel.
New surfaces of concrete or cement mortar should be painted one month after construction.
Surfaces already painted must be completely cleaned with chemical or mechanical means and sanded to a smooth finish.
The wet surface must be allowed to dry for at least 3 – 5 days prior to the paint application.

PRIMING
Prime surfaces with EPOXITE DUR primer.

APPLICATION
Components Α (resin) and Β (hardener) are already packed in separate containers with a preset mixing ratio. Any modification of the mixing ratio will result in improper polymerization of the mixture.
Mix the 2 components after careful mix of each component separately.
Stirring is done carefully for 3-5 minutes taking care to ensure thorough mixing of the two components on the walls and the bottom of the pail.
Imperfect mixing will result in uneven curing of the coating with parts that will not cure at all.
After mixing of the two components allow 10 – 15 minutes and then apply the coating as is or diluted up to 5% with polyurethane solvent.
Application is done with a brush, roller or spray gun in two or three coats.
The paint obtains its final properties 7 – 10 days after the application of the finishing coat.

REMARKS
PREMIUM POOL PAINT contains solvents and during application good ventilation of the space should be ensured.
It is advisable the use of protective clothing, gloves and mask with filter suitable for solvents.
The coated surface should be protected from humidity for 36 – 48 hours.
Should recoating be carried out after 15 days, the surface must be sanded with a coarse sandpaper and dust must be removed.
Curing as well as pot – life are affected by ambient temperature and humidity. Low temperatures and high humidity tend to increase pot – life while high temperatures and low humidity shorten the pot life.
Before using PREMIUM POOL PAINT read carefully all instructions and information relevant to its safe and best use.
Treatments such as sanding, welding, burning off, etc. of paint films may generate hazardous dust and/or fumes. Work in well ventilated areas. Use suitable personal (respiratory) protective equipment, as necessary

LEAD STATEMENT
WARNING: Treatment of old surfaces such as dry sanding, flame cutting and/or welding of the dry paint film will give rise to dust and/or hazardous fumes. Lead dust may be released. Lead is toxic. Exposure to lead dust can cause serious illness. Wet sanding/flatting should be used wherever possible. If exposure cannot be avoided by the provision of local exhaust ventilation, suitable respiratory protective equipment should be used.

RUSTOLEUM ANTI-SLIP ADDITIVE 700GR

/

Anti-slip quartz sand for use with two-component floor paints.

Fully slip-resistant finish
Easy application
Good adhesion

DESCRIPTION
RUST-OLEUM® Hard Hat Aerosols Anti-Slip 2400 are based on a fast drying acrylic modified
short oil alkyd. The coloured products are based on lead- and chromate free pigments and
contain a special anti-slip additive.

RECOMMENDED USES
RUST-OLEUM Anti-Slip 2400 should be applied on metal, concrete, ceramic and wood surfaces or properly prepared painted substrates. Steel should be primed with 2169 or 2182.
RUST-OLEUM Anti-Slip 2400 are intended for small maintenance jobs or for touch-up.
RUST-OLEUM Anti-Slip 2400 should be used interior/exterior in light industrial exposures
where anti slip characteristics are required.

TECHNICAL DATA
Appearance: Satin
Colour: See colour card
Propellant: Butane/propane
Recommended film thickness: 25 µm dry, equals averagely 100 µm wet
VOC-content: 524 – 538 g/l
Drying times 20°C/50% r.v.
To touch: 20 minutes
To handle: 60 minutes
To recoat: After 1 hour with itself
Full hardness 7 days
Heat resistance: 100°C (dry heat), above 65°C discoloration may occur

Coverage
Theoretical: 2.5 m² per spray can at 25 µm dry
Practical: Practical coverage depends on many factors such as porosity and roughness of
the substrate and material losses during application.

SURFACE PREPARATION
Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means.
Sand intact coatings to provide a proper key for adhesion. The surface must be clean and dry
during application.

DIRECTION FOR USE
Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is
heard. Shake frequently during use. Hold the can approx. 25 cm from surface. Use back and
forth motion keeping can parallel with surface. Ensure that can is in motion when spray button
is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to
achieve adequate coating thickness. After use turn can upside down and press spray button
for 2 – 3 seconds to clean valve.

REMARKS
Not for use in wet areas such as bathrooms and on substrates, which are regularly in contact
with, water.

APPLICATION CONDITIONS
For good results the relative humidity shall be below 85% and the temperature of the can and
substrate above 10°C.

V33 EXTREME TRAFFIC SATIN FLOOR PAINT 500ML WHITE

/

Floor Trafic Extrême satin paint V33
Resistance to repeated passages of cars: wear and hot tires.
Insensitive to stains and grease.
High resistance to scratches and impacts, tool puncturing, abrasion, without flaking.
Washable with detergents and high pressure cleaner.
Yield: 0.5L = 7m²

Shopping Cart